See MICCRO XP-2000 MSDS

1. XP-2000 should be stirred prior to usage and periodically if not used for extended periods of time.

2. Chemically and/or mechanically clean the area of the part to be masked. The area to be masked must be free of all dirt, oil or other contaminants. Cleaning is the most critical aspect of the masking procedure.

3. Apply XP-2000 to the area to be masked by dipping or brushing. For reducing XP-2000, use XP-2000 REDUCER only.

4. Apply a minimum of two coats depending upon the type of plating/chemical solution and/or length of pro cessing time in solution. Allow at least 30 minutes air-dry time between coats and overnight air-dry time after application of final coat before introduction into solution. Faster drying of XP-2000 can be accom plished by force drying for 15 minutes in an oven not exceeding 140_ F or over a hot plate not exceeding 140_ F for 15 minutes. Drying over a hot plate is preferable to oven drying. Drying time will vary according to relative humidity. NOTE: Make sure XP-2000 has lost all solvent odor before force drying or applying additional coats.

5. XP-2000 will not withstand extended periods in hot alkaline solutions. Two (2) minutes is the maximum time permitted.

6. XP-2000 can normally be peeled from the part after use if the part is warm. For mass stripping or removal from recessed areas, use: 1. XP-2000 Reducer; 2. Toluene; 3. Miccrostrip A. The first two are the fastest.

CHARACTERISTICS

Color:: Orange
Viscosity: 5000-6000 cps
Coverage Rate: Approx. 130 sq. ft. (12 m2) per gallon, 12 mli dry film.
WtlGal.: 7.90 Ibs./gal.
Flash Point: 24_ F. TCC

XP-2000 is available in: 1 gal., 5 gal., and 55 gal. containers.


PRECAUTIONARY INFORMATION

CONTAINS VOLATILE SOLVENTSKeep away from sparks and open flame. Store at temperatures above 32_ F and below 105_ F. Keep containers closed when not in use. Maintain adequate ventilation in working area. Wear approved respirators and protective clothing when working in confined areas. Avoid repeated breathing of concentrated vapors. Prolonged contact of liquid material with skin may be irritating. If material comes in contact with skin, wash skin surface thoroughly with soap and water. In case of eye contact, flush eyes thoroughly for 15 minutes with water and consult a physician. REFER TO MATERIAL SAFETY DATA SHEET FOR ADDITIONAL WARNINGS AND INFORMATION.

 

WARRANTY DISCLAIMER. Based upon Seller's experience, the information contained herein is believed to be reliable. Seller requests that Purchasers and users inspect and test Seller's products as to contents and suitability for a particular purpose. Seller disclaims any express warranties and nothing contained herein shall constitute any warranty, whether express or implied, and Seller hereby DISCLAIMS ALL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Additionally, Seller makes no warranties concerning the compliance of products with any state, local, or federal laws or regulations and Purchaser assumes full responsibility for complying with such laws, regulations, codes and requirements. Seller makes no warranty concerning and does not assume in this or any other document any obligation or liability in connection with patent infringement suits brought against Purchaser, user and/or Seller with respect to Seller's products. The EXCLUSIVE REMEDY for all proven claims whether through negligence, strict liability, tort or otherwise is limited to an amount equal to the price of the particular products or services giving rise to the liability, or, at the election of the Seller, the replacement of the product in question. In no event shall Seller be liable to Purchaser for any incidental, consequential, indirect, or special damages, including without limitation, lost revenues or profits, even if Seller was advised of the possibility of such lost revenues or profits (subject to state by state application of MagMoss [16CFR701.3]).