See T-100 MSDS

Return to Products List

DESCRIPTION

T-100 is a clear primer adhesive formulated to achieve optimum adhesion under a wide range of application conditions when used in conjunction with PLASTISOL In addition to being an excellent general purpose primer, it is especially resistant to hot alkaline solutions.
T-100 has been formulated to comply with the solvent requirements of Rule 66 of the Los Angeles Air Pollution Control District and Regulation 3 of the San Francisco BayAreaAir Pollution Control District.

PROPERTIES

Color: Clear to pale yellow
Viscosity: 31 sec. #1 Zahn
Solids: 16%bywt.
Flashpoint: 43_F
Coverage: 380 sq. ft./gal. 0.3 mils
Wt./gal: 7.1 Ibs.

APPLICATION

1. Clean metal. For best adhesion metal must be physically and chemically clean. Sandblasting with clean sand or pickling and degreasing are satisfactory.
2. Apply primer by dipping, brushing or spraying. Air dry for 15 min utes and bake at 360_ to 400F for 15 to 45 minutes, depending upon metal mass and oven efficiency.
3. While metal is hot, dip into the PLASTISOL and leave until the desired coating is formed. The thickness film is determined by the amount of heat in the metal and length of time in the PLASTI SOL.
4. Evaporated solvent should be replaced with T-100 primer reducer only.

SEE BACK FOR PRECAUTIONARY INFORMATION

DESCRIPTION

T-200 Primer is a high solids, white pigmented primer-adhe sive formulated to achieve optimum adhesion when used with PLASTISOL coatings. It meets the specifications of MIL-P-20689A.
T-200 Priimer has been formulated to comply with the solvent requirements of Rule 66 of the Los Angeles Air Pollution Control Dis trict and Regulation 3 of the San Francisco Bay Area Air Pollution Control District. It is expected to comply with similar air pollution control regulations in other areas.

PROPERTIES

Color : White
Viscosity : 34 to 38 seconds #1 Zahn
Solids : 25%
Flashpoint: 38 +~ 6_F
Wt./gal : 7.4 to 7.8 Ibs.

APPLICATION

1. Clean metal. For best adhesion, metal must be physically and chemically clean. Sandblasting with clean sand or pickling and degreasing are satisfactory.
2. Apply primer by dipping, brushing or spraying. Air dry for 15 minutes and bake at 350_F to 400_F for 15 to 45 minutes, depending on metal mass.

HANDLING INSTRUCTIONS

1. T-200 requires periodic mechanical agitation to prevent pigment and resin settling: When hard settling ocurs, as is common after truck transportation, the settled material should be pulled up from the bottom with a hoe or similar bladed implement to agitate. Normally this is required only at the outset, but is essential for optimum results.
2. Evaporated solvent should be replaced with T-200 Reducer so that the viscosity and solids balance are maintained within the range of material as shipped.

 

T-300 WATER-BASED PLASTISOL PRIMER

Return to Products List

DESCRIPTION

T-300 is a low V. O. C., cross-linked, acrylic polymer coating which was developed in response to the V. O. C. problem with conventional solvent-based primers. T-300 achieves optimum water-base adhesion for a wide range of applications when used in conjunction with plastisol.

PROPERTIES

Color: Milky White
Viscosity: 26 sec., #1 Zahn Cup
PH: 7.1
% Solids : 13.0
V. O. C. (#/Gal.): 1.92
Wt./Gal: 8.53 #/gal.
Coverage 380 sq. ft/gal. at 0.3 mils

PRECAUTIONARY INFORMATION

Keep from freezing. Keep containers closed when not in use.
STORAGE: This coating material should be stored and used in accordance with normal standards of good practice for handling industrial paints.

APPLICATION

1. Clean metal thoroughly by sandblasting, pickling or degreasing. Metal part must be free of oil, grease, dirt, old coating or other contaminants.
2. Apply primer by dipping or brushing and allow to thoroughly air dry. This could be from 2-3 hours depending on air conditions.
3. Bake part in 350_F to 375_F oven until part reaches 305_F.
4. Remove part from oven and dip into plastisol. Leave part in plas tisol until desired coating thickness is maintained.

USE: Maintain adequate ventilation in working area. In case of eye contact, flush thoroughly with water for 15 minutes and consult a physician.

T-100 and T-200 PRIMERS CONTAIN VOLATILE SOLVENTS: Keep away from sparks and open flame. Store at temperatures above 32_ F and below 105_ F. Keep containers closed when not in use. Maintain adequate ventilation in working area. Wear approved respirators and protective clothing when working in confined areas. Avoid repeated breathing of concentrated vapors. Prolonged contact of liquid material with skin may be irritating. If material comes in contact with skin, wash skin surface thoroughly with soap and water. In case of eye contact, flush eyes thoroughly for 15 minutes with water and consult a physician.

REFER TO MATERIAL SAFETY DATA SHEET FOR ADDITIONAL WARNINGS AND INFORMATION.

WARRANTY DISCLAIMER. Based upon Seller's experience, the information contained herein is believed to be reliable. Seller requests that Purchasers and users inspect and test Seller's products as to contents and suitability for a particular purpose. Seller disclaims any express warranties and nothing contained herein shall constitute any warranty, whether express or implied, and Seller hereby DISCLAIMS ALL WARRANTIES OF MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE. Additionally, Seller makes no warranties concerning the compliance of products with any state, local, or federal laws or regulations and Purchaser assumes full responsibility for complying with such laws, regulations, codes and requirements. Seller makes no warranty concerning and does not assume in this or any other document any obligation or liability in connection with patent infringement suits brought against Purchaser, user and/or Seller with respect to Seller's products. The EXCLUSIVE REMEDY for all proven claims whether through negligence, strict liability, tort or otherwise is limited to an amount equal to the price of the particular products or services giving rise to the liability, or, at the election of the Seller, the replacement of the product in question. In no event shall Seller be liable to Purchaser for any incidental, consequential, indirect, or special damages, including without limitation, lost revenues or profits, even if Seller was advised of the possibility of such lost revenues or profits (subject to state by state application of Mag-Moss [16CFR701.3]).