.

Home  |  Products  |  Contact Tolber  |  Distributors  |  Special Offers

TolberSeal
A High Performance Inorganic Corrosion Inhibitor for Aluminum Alloys

Coating thickness is less than 2 microns
Does not effect dimensional tolerances
Retains total electrical and heat conductance
Will not chip, flake, or peel
Accomodates temperatures from -80°F to +750°F
Meets Ford Motor Company Specifications ESE-M2P128A
Meets GM-4350M-B168
Unaffected by brake or engine fluids
Can be applied before or after most required impregnation processes

 

TolberSeal has been Salt Spray tested according to ASTM-B-117

Cast Aluminum (depending on alloy) 336 hours
   
Automotive  
319 alloy 250 hours
356 alloy 336 hours
   
Wrought Aluminum (rolled, sheet, bar)  
6061 alloy 1332 hours
2024 alloy 1500 hours


INSTRUCTIONS:

1. Dilute the concentrated TOLBERSEAL to approximately 10% solution in water.

2. After the Chromate Conversion Process, dip for 30-40 seconds in TOLBERSEAL/water solution..

3. Immediately after 30-40 second dip, rinse in clean water for 30-40 seconds.

4. Allow part to age for 24 hours after rinse. *

* Ageing times for TOLBERSEAL are consistent with the ageing times of most Chromate Conversion Operations.

***** TOLBERSEAL is available in 1 gal, 5 gal, and 55 gal containers *****



PRECAUTIONARY INFORMATION

CONTAINS VOLATILE SOLVENTS -- Keep away from sparks and open flame. Store at temperatures above 32°F and below 105°F. Keep containers closed when not in use. Maintain adequate ventilation in working area. Wear approved respirators and protective clothing when working in confined areas. Avoid repeated breathing of concentrated vapors. Prolonged contact of liquid material with skin may be irritating. If material comes in contact with skin, wash skin surface thoroughly with soap and water. In case of eye contact, flush eyes thoroughly for 15 minutes with water and consult a physician. REFER TO MATERIAL SAFETY DATA SHEET FOR ADDITIONAL WARNINGS AND INFORMATION.

TOLBER DIVISION EMERGENCY PHONE NUMBER

1-800-424-9300


WARRANTY DISCLAIMER. Based upon Seller's experience, the information contained herein is believed to be reliable. Seller requests that Purchasers and users inspect and test Seller's products as to contents and suitability for a particular purpose. Seller disclaims any express warranties and nothing contained herein shall constitute any warranty, whether express or implied, and Seller hereby DISCLAIMS ALL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Additionally, Seller makes no warranties concerning the compliance of products with any state, local, or federal laws or regulations and Purchaser assumes full responsibility for complying with such laws, regulations, codes and requirements. Seller makes no warranty concerning and does not assume in this or any other document any obligation or liability in connection with patent infringement suits brought against Purchaser, user and/or Seller with respect to Seller's products. The EXCLUSIVE REMEDY for all proven claims whether through negligence, strict liability, tort or otherwise is limited to an amount equal to the price of the particular products or services giving rise to the liability, or, at the election of the Seller, the replacement of the product in question. In no event shall Seller be liable to Purchaser for any incidental, consequential, indirect, or special damages, including without limitation, lost revenues or profits, even if Seller was advised of the possibility of such lost revenues or profits (subject to state by state application of Mag-Moss [16CFR701.3]).

 

Back to Top

Home  |  Products  |  Contact Tolber  |  Distributors  |  Special Offers

We accept:

 
Tolber Chemical
220 West 5th St.  * Hope, Arkansas  *  71801
Phone 870-777-3251 or Fax 870-777-8056

E-mail us at tolbermail@sbcglobal.net