See MICCROSTOP MSDS

Return to MICCRO Products List

MICCROSTOP is suitable for use in the following cycles:

High-Speed Copper Tin
Chrome (Decorative) Zinc
Phosphate Coatings Gold
Alloy Coatings Silver
Heavy Deposit Industrial Chrome
Nickel, Cadmium, Gold on Silver, Silver on Gold

APPLICATION PROCEDURE

1. Chemically and/or mechanically clean the area of the part to be masked. The area to be masked must be free of all dirt, grease, oil or other contaminants. Cleaning is the most critical aspect of the masking procedure.

Apply MICCROSTOP to the area to be masked by dipping, brushing, or spraying. Appropriate dilution of MICCROSTOP is required for spraying. For reducing MICCROSTOP, use MICCROSTOP REDUCER only.

Apply a minimum of two successive coats of MICCROSTOP to the area to be masked, allowing a minimum of 30 minutes air-dry time between coats and overnight air-dry time after final coat before introduction into solution. Faster drying of MICCROSTOP can be accomplished by force drying for 15 minutes in an oven not exceeding 140_ F, or over a hot plate not exceeding 140_ F. Drying time will vary according to relative humidity. NOTE: Make sure MICCROSTOP has lost all solvent odor before force drying or applying additional coats.

For extra long cycles, 3 coats are recommended.

5. MICCROSTOP can be removed using MICCROSTOP REDUCER or MiCCROSTRIP A.

CHARACTERISTICS

Color:

Transparent Red
Viscosity: 32-37 sec #2 Zahn
Coverage Rate: Approx. 500 ft.2 (46 m2) per gallon,
1.0 mil dry film.

WtJGal.: 7.50 Ibs./gal.
Flash Point: 24_ F. TCC

MICCROSTOP is available in: 1 gal., 5 gal., and 55 gal. containers.

Developed and manufactured by experienced platers and coalers

PRECAUTIONARY INFORMATION

CONTAINS VOLATILE SOLVENTS _ Keep away from sparks and open flame. Store at temperatures above 32_ F and below 105_ F. Keep containers closed when not in use. Maintaln adequate ventilation in working area. Wear approved respirators and protective clothing when working in confined areas. Avoid repeated breathing of concentrated vapors. Prolonged contact of liquid material with skin may be irritating. If material comes in contact with skin, wash skin surface thoroughly with soap and water. In case of eye contact, flush eyes thoroughly for 15 minutes with water and consult a physician. REFER TO MATERIAL SAFETY DATA SHEET FOR ADDITIONAL WARNINGS AND INFORMATION.

TOLBER DIVISION EMERGENCY PHONE NUMBER   1-800-264-2535 extension 2584

WARRANTY DISCLAIMER. Based upon Seller's experience, the information contained herein is believed to be reliable. Seller requests that Purchasers and users inspect and test Seller's products as to contents and suitability for a particular purpose. Seller disclaims any express warranties and nothing contained herein shall constitute any warranty, whether express or implied, and Seller hereby DISCLAIMS ALL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Additionally, Seller makes no warranties concerning the compliance of products with any state, local, or federal laws or regulations and Purchaser assumes full responsibility for complying with such laws, regulations, codes and requirements. Seller makes no warranty concerning and does not assume in this or any other document any obligation or liability in connection with patent infringement suits brought against Purchaser, user and/or Seller with respect to Seller's products. The EXCLUSIVE REMEDY for all proven claims whether through negligence, strict liability, tort or otherwise is limited to an amount equal to the price of the particular products or services giving rise to the liability, or, at the election of the Seller, the replacement of the product in question. In no event shall Seller be liable to Purchaser for any incidental, consequential, indirect, or special damages, including without limitation, lost revenues or profits, even if Seller was advised of the possibility of such lost revenues or profits (subject to state by state application of MagMoss [16CFR701.3]).